Gate Won't Open or Close? Stuck Gate Repair in McKinney
A gate that refuses to move, or moves part of the way and quits, is telling you something specific. How it fails, and where in its travel it stops, usually points to the cause before any tools come out.
Open 24 hours, 7 days a week

What your stuck gate is doing
Stuck open and will not close
The operator is usually waiting on a safety input. A photo eye knocked out of line by a mower, a loop that thinks a car is parked on it, or a hold-open timer set too long will all keep a gate parked open.
Stuck closed and will not open
Check whether the board has power first. If the lights are on and the gate still sits there, a blown fuse, a failed receiver, a tripped force limit or the motor itself is more likely.
Opens halfway, then stops
A gate that quits at the same spot each time often meets a tight point in its travel: a raised section of driveway, a dry hinge, a bent track joint or a limit that has drifted.
Reverses for no clear reason
Most operators back up when they sense extra effort. Wind against a solid privacy gate, a sagging leaf rubbing the concrete or a force setting turned too low can all set it off.
Crawls or grinds as it moves
Slow travel points to a tired battery or a weak motor. Grinding or clicking usually comes from a stripped gear, a worn roller or a chain skipping a sprocket tooth.
Motor hums but the gate stays put
Humming with no movement often means the operator is still in manual release, the arm is binding, or a capacitor or gearbox has failed.
Why gates get stuck open or stuck closed
A powered gate has a short list of reasons for not moving. It may have no power, it may be receiving a signal that tells it to stay put, the operator may have failed, or the gate itself may have become too hard to push. Separating those four is most of the diagnosis, and it is the order we work in when we arrive.
Stuck open tends to be a signal problem, where something is telling the operator that a car or a person is in the opening. Stuck closed tends to be a power or mechanical problem. That is not a rule, but it is the right place to start looking.
Gate opens halfway then stops
When a gate stops partway, note exactly where. If it is the same spot every time, the cause is usually physical. Ground movement in our clay soil can lift one slab of a driveway enough for a swing gate to scrape it, and a sliding gate can hang on a bent track joint or a seized roller.
If it stops at a different place each time, the operator is more likely misreading its own travel. Worn limit switches, a slipping encoder or a battery that sags under load can all cut a cycle short. We test the gate by hand with the operator released, then run it under power and compare the two.
Grinding, dragging and a gate off its track
A sliding gate that comes off its track will often keep trying to run, and that is when gears, rack teeth and chain brackets get damaged. If the gate has jumped the rail, leans hard on the guide rollers or drags on the concrete, stop running it and call.
Typical repairs for a gate that drags, grinds or binds include:
- Roller, guide roller and track repair on sliding gates
- Chain tension and sprocket checks where a chain keeps jumping
- Hinge and arm adjustment on swing gates that drag or hit a post
- Limit and force recalibration once the mechanical fault is fixed
- Gearbox, motor and control board replacement when a part has failed
Power outage recovery and the manual release
Storms that knock out power across Collin County often leave gates sitting wherever they stopped. Battery backed operators should keep running on reserve, but a battery that was already weak may manage a cycle or two and then quit. Once power returns, some boards need a reset or a fresh learn of their open and close limits before they behave normally.
If you need the gate open before help arrives, use the manual release that came with your operator. It disconnects the motor so the gate can be pushed by hand. Switch the power off first, keep clear of the arm, and secure the gate once it is where you want it.
What affects the cost
The price depends on what the fault turns out to be. Realigning a photo eye and replacing a gearbox are very different jobs, and a gate that has been run off its track may need track, roller and operator work together. Call for pricing, and ask about current discounts.
Check these before you call
- Look for lights on the control board or a status light on the operator
- Check the breaker or the outlet that feeds the gate
- Make sure nothing sits between the safety sensors or across the loop in the drive
- Try a second remote to rule out a dead remote battery
- Note where the gate stops and any noise it makes, and mention it when you call
Safety first
Never stand in the path of a gate that is stuck partway, because it can start moving again without warning when a sensor clears or power comes back. Do not try to force a gate that is still engaged with its motor, and keep hands away from chains, rollers and hinge points. If you are unsure whether the operator is released, switch the power off at the breaker first.
Common questions
Why does my gate open but not close?
Nearly always a safety input. A blocked or misaligned photo eye, a loop that reads a vehicle, or a stuck open command will keep it open. If the sensors look clear, call and we will trace which input the board is seeing.
My gate stopped working after a storm. Is the motor dead?
Not necessarily. Storms often trip breakers, drain batteries or soak a control box. Check the power and battery first. If the board stays dark, it may have taken a surge, which we can test on site.
Can I keep using a gate that grinds?
It is better not to. Grinding usually means a gear, roller or chain is damaged, and each extra cycle makes it worse. Release the operator, leave the gate open or closed by hand, and call.
Is a stuck gate an emergency?
If it traps cars inside or leaves a property unsecured overnight, treat it as one. We take calls 24/7, so call (469) 634-3100 whenever it happens and we will talk through the next step.
What does stuck gate repair cost?
It depends on the cause, which can be anything from a sensor alignment to a new gearbox or track work. Call (469) 634-3100 for pricing and ask about current discounts.
Related gate services
Need stuck gate repair in McKinney?
Open 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.