Gate Welding and Frame Repair in McKinney
Iron and steel gates rarely fail all at once. A weld cracks at a hinge, a crossbar lets go, or a bumper knocks the frame out of square. Welding the damage and reinforcing what caused it can often save a gate that still has plenty of life left.
Open 24 hours, 7 days a week

Signs you need this repair
A weld has cracked at the hinge
The hinge joint carries the full weight of the leaf on every swing. A hairline crack there keeps growing until the gate drops, so it pays to catch it early.
The frame is bent or out of square
A vehicle bump, a gust against a solid panel or a gate forced past its stop can rack the frame. It then drags, binds or refuses to latch.
Pickets or crossbars are loose
Rust at the joints or a broken weld lets pickets rattle or fall out, which looks rough and can leave gaps a dog can slip through.
The opener bracket has torn loose
Operator arm brackets are often a small plate welded or bolted to the gate. When one cracks, the gate stalls or moves unevenly even though the opener itself is fine.
Rust is bubbling through the paint
Surface rust can be cleaned and treated. Rust that has eaten through a rail or the bottom of a post needs the bad metal cut out and replaced.
Track or roller brackets have failed
On sliding gates, a broken chain bracket, roller bracket or cracked track weld can derail the gate or keep the drive from pulling it.
Gate welding repair for iron, steel and aluminum
Most driveway gates in McKinney neighborhoods are steel or wrought-iron style, and the damage on them tends to show up at the joints: hinges, crossbars, picket ends and brackets. Steel and iron are welded differently from aluminum, so tell us the material when you call, or send a photo if you are not sure.
Much of this work can be done right at the gate without hauling it away. Before any welding starts, the leaf is supported and the opener is disconnected so nothing moves while the repair is made.
Broken frame repair and reinforcement
A bent frame can sometimes be straightened in place. When a rail is kinked or torn, it is usually better to cut out the damaged section and weld in new steel. Wide gates and solid privacy panels often need extra bracing, because their own weight and the wind keep pulling the frame out of square.
Common welding and structural repairs include:
- Broken frame and crossbar repair
- Bent frame straightening and panel replacement
- Hinge welding and new weld-on hinges
- Operator bracket fabrication and support bracket welding
- Chain, roller and track bracket welding on sliding gates
- Picket replacement and diagonal reinforcement
Vehicle impact and storm damage repair
Gates close to the street take hits from delivery trucks, trailers and the occasional driver who misjudges the opening. Spring storms in north Collin County add hail, falling limbs and wind strong enough to bend a gate that is caught half open. After any impact, look at the hinges, the post and the opener bracket, not just the dented part.
A gate that was struck may also need a post reset or new hinges. We look over the whole hinge side so a repaired gate is not left hanging on a damaged post.
Rust repair, corrosion treatment and repainting
Humid summers, lawn sprinklers and puddles that sit against the bottom rail all work on bare steel. Rust repair starts with removing loose scale, cutting out metal that has lost its strength, and welding in new steel where it is needed. The repair is then primed and painted to slow the next round of corrosion.
Many HOAs in the master-planned neighborhoods around McKinney, Prosper and Celina set rules for gate color and finish. Check your guidelines before choosing a new paint so the repaired gate stays within them.
What affects the cost
The price depends on how many welds are needed, whether new steel has to be fabricated, the size and material of the gate, whether the leaf has to come off its hinges, and how much painting follows. Call for pricing, and ask about current discounts.
Check these before you call
- Look closely at each hinge joint for cracks in the weld
- Sight along the top rail to see whether the frame is bent
- Check the opener bracket on the gate for movement or cracks
- Note any recent vehicle contact or storm damage
- Photograph the damage up close and from a distance for the quote form
Safety first
A gate with a cracked hinge weld can drop suddenly. Keep people and vehicles out of its path, and switch off the opener so it does not keep pulling on a damaged frame. Sharp edges on torn steel cut easily, so wear gloves if you have to move the gate by hand.
Common questions
Can you weld my gate without taking it down?
Often, yes. Many hinge, bracket and frame welds can be done in place with the gate supported. Larger rebuilds may mean taking the leaf off its hinges.
Should I repair a bent gate or replace it?
If the frame is mostly sound and the damage is in one area, repair usually makes sense. Rust throughout, several torn rails or a gate that never hung right are reasons to look at a new one.
Can aluminum gates be repaired?
Many can, but aluminum needs a different welding process, and some cast parts are better replaced than welded. Tell us the material and send a photo so we can talk through the options.
Can you make a new bracket for my gate opener?
Yes. When the original bracket is broken or was never strong enough, a new operator bracket can be fabricated and welded or bolted to the gate.
How much does gate welding cost?
It depends on the number of repairs, any new steel, painting, and whether the gate has to come down. Call (469) 634-3100 for pricing and ask about current discounts.
Related gate services
Need gate welding & frame repair in McKinney?
Open 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.