Gate Post and Hinge Repair in McKinney, TX
A swing gate can only hang as straight as the post it is bolted to. When a post leans or a hinge wears out, the latch side drops, the gate drags, and the opener ends up fighting it. We repair the post and hardware so the gate hangs true again.
Open 24 hours, 7 days a week

Signs you need this repair
The post leans away from the opening
A hinge post that tips a little lowers the far end of the gate by a lot more. On clay soil this usually means the footing has rotated or the concrete has cracked below the surface.
The gate sags at the latch
Worn hinge pins, a bent hinge bracket or a loose weld let the leaf drop. The latch stops catching, and on a double gate the two leaves no longer meet in the middle.
A post is rusted at the base
Steel posts set straight into concrete can trap water right where the metal meets the slab. Rust there is often worse than it looks from above, and a thin wall can fold under the weight of the gate.
Hinges squeal, pop or bind
Dry or seized hinges make the gate hard to move and can trip the opener force setting. A popping sound often means a pin or bearing has worn through.
The latch post has moved
If the gate still swings well but will not latch or lock, the latch post or the drop rod hole may have shifted, not the hinge side.
The post was hit or bent
A vehicle bump, a falling limb or a strong storm can bend a post or crack its footing. A bent steel post usually has to be replaced rather than pulled back into line.
Leaning gate post repair and replacement
A gate post leans for one of three reasons: the footing was too small for the gate, the soil around it has moved, or the post itself has rusted or rotted. We work out which one it is before deciding anything, because resetting a post in the same undersized hole tends to end with the same lean a few seasons later.
Depending on what we find, a post can be straightened and anchored, reset in a new concrete footing, or replaced. Wood yard gates usually hang on 4x4 or 6x6 posts, while iron and steel driveway gates hang on heavier square or round steel. A double swing gate, or any gate with an opener arm pushing on it, often needs a larger post and a deeper footing than the original builder used.
Concrete footings in Blackland clay
Much of McKinney and the towns north of it sit on dark Blackland Prairie clay. It swells after heavy rain and shrinks and cracks in a dry summer, and that movement pushes on a post footing from every side, year after year. A footing that held a light fence gate can loosen once a heavier iron leaf or an opener is added.
When we pour a new footing, the goal is a hole sized for the gate weight and swing, with the concrete shaped to shed water away from the post. On steel posts we can add corrosion protection at the base, and on surface-mounted posts we replace damaged base plates and anchor bolts.
Gate hinge replacement and alignment
Hinges are the wear part on a swing gate. Driveway and yard gates around here use weld-on barrel hinges, adjustable bolt-on hinges, ball-bearing hinges for heavy leaves, and pivot hinges that carry the gate from the bottom. Swapping a worn hinge for the right type, or upgrading a heavy gate to ball-bearing or adjustable hinges, often takes the sag out without touching the post at all.
Hinge and hardware work we commonly handle includes:
- Upper and lower hinge replacement on single and double gates
- Weld-on hinge replacement and hinge welding on iron and steel
- Hinge bracket, gate pivot and bearing replacement
- Hinge alignment, adjustment and lubrication
- Anti-sag reinforcement, such as diagonal bracing or a cable kit on wood gates
Latches, drop rods, cane bolts and gate stops
The latch side matters as much as the hinge side. A drop rod or cane bolt holds the inactive leaf of a double gate in place, a gate stop gives the leaf a fixed end point, and hold-open hardware keeps it from blowing shut. When any of these bends or goes missing, the force lands somewhere else, usually on the hinges.
We replace worn latches, gate lock hardware, drop rods, stoppers and hold-open catches, and realign the strike so the gate closes and latches cleanly.
What affects the cost
The price depends on whether the post can be reset or has to be replaced, the size and material of the post, how much concrete is needed, whether a driveway or pavers have to be cut, and which hinges the gate needs. A hinge swap and a new steel post on a fresh footing are very different jobs. Call for pricing, and ask about current discounts.
Check these before you call
- Stand back and sight along the hinge post to see whether it leans
- Compare the gap at the top and bottom of the latch side
- Look for cracks in the concrete around the base of each post
- Check the hinges for loose bolts, broken welds or flaking rust
- Take a photo of the hinge side and send it with the quote form
Safety first
A leaning post can give way without warning, and a driveway gate is heavy. Keep children and pets away from a gate that sags badly, and do not hang on it or try to lever a post back by hand. If the gate has an opener, switch it off until the post is checked so the motor is not pulling against it.
Common questions
Can a leaning gate post be straightened, or does it need replacing?
It depends on why it leans. A sound post in a loose footing can often be reset and anchored. A post that is bent, rusted thin or rotted at the base should be replaced.
Why does my gate sag when the post looks straight?
Worn hinges, a cracked hinge weld or a frame that has racked out of square can all drop the latch side. We check each one before recommending work.
Do you work on wood gate posts as well as steel?
Yes. We repair and replace wood, iron and steel gate posts, including the hinge post and the latch post on single and double gates.
How much does gate post replacement cost?
It depends on post size and material, footing depth, any concrete or paver cutting, and the hinges the gate needs. Call (469) 634-3100 for pricing and ask about current discounts.
Will fixing the post help my gate opener?
Usually, yes. An opener pushing a sagging or binding gate works harder on every cycle, which wears the motor and trips force limits. Once the gate swings freely, we recheck the opener settings.
Related gate services
Need gate post & hinge repair in McKinney?
Open 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.