Skip to content
McKinneyGate Repair · 24/7

Gate Safety Sensor and Vehicle Loop Repair in McKinney

Safety sensors keep a gate from closing on a person or a car, and vehicle loops tell it when a car is waiting to leave. When either one fails, the gate refuses to close, turns around for no reason, or opens with nobody there.

Open 24 hours, 7 days a week

Cleaning and aligning a pair of gate safety photo eyes

Signs you need this repair

Photo eye and infrared sensor troubleshooting

Photo eyes send an infrared beam across the driveway. When the beam is broken, the opener stops or reverses. Alignment is the most common fault: a sensor clipped by a mower, a post that shifted with the soil, or a bracket shaken loose can leave the beam just off target.

We clean, realign, troubleshoot and replace photo eyes, including retro-reflective units that bounce the beam off a reflector and through-beam pairs with a separate transmitter and receiver. Where one sensor is covering a wide opening, adding coverage may be worth a conversation.

Safety edges and entrapment protection

A safety edge is a pressure-sensitive strip on the leading edge of a gate or on a post. When it is pressed, the gate reverses. Edges crack in the sun, get torn by bumpers and lose their connection where the cable flexes, and wireless edges add a transmitter battery that eventually runs down.

UL 325 and ASTM F2200 describe how gate operators and their entrapment protection are expected to perform. We test each sensor and edge to see that it stops and reverses the gate the way those standards expect, and we point out gaps such as an unprotected pinch point at a sliding gate post or missing warning signs.

Vehicle detection loops and loop detectors

A vehicle loop is a coil of wire set into a saw cut in the driveway and connected to a loop detector inside the opener. An exit loop, sometimes called a free-exit loop, opens the gate for cars leaving. A shadow loop or safety loop under the gate path keeps it from closing on a car. Some properties use an above-ground vehicle detector or a buried magnetic sensor instead.

Loops in north Collin County sit in concrete that moves. As the clay underneath shrinks and swells, slabs crack and a crack across the saw cut can stretch or snap the wire. Water then gets in, and the loop fails on and off before it quits for good. We test the loop and the detector separately, then repair, replace or reprogram whichever one is at fault.

Loop installation, saw cutting and sensor wiring

Replacing a damaged loop means cutting a new slot, laying new loop wire, sealing the cut, and running lead-in wire back to the opener, sometimes through new conduit. On a driveway that is about to be poured, a preformed loop can be set before the concrete goes in. Low-voltage sensor and loop wiring is part of our work. If the opener needs a new line-voltage circuit, a licensed electrician handles that part.

Sensor and loop work we handle includes:

  • Photo eye installation, replacement and alignment
  • Safety edge installation and replacement, including wireless edges
  • Exit, shadow and safety loop replacement
  • Loop detector replacement and programming
  • Underground sensor wiring repair
  • Gate safety inspections and warning sign replacement

What affects the cost

The price depends on whether a sensor needs cleaning and alignment or replacement, how many loops are involved, the length of any new saw cut, and whether wire has to be trenched or pulled through conduit. Call for pricing, and ask about current discounts.

Check these before you call

  • Wipe both photo eye lenses with a soft cloth and look for webs, mud or wasps
  • Make sure nothing is parked or stored in the gate path
  • Check whether the indicator lights on the photo eyes are steady
  • Look for cracks or broken sealant over any loop cuts in the driveway
  • Note whether the problem shows up at a certain time of day or after rain

Safety first

Never tape over, unplug or jumper a safety sensor to make a gate close. Those devices exist because gates can seriously injure people, children most of all. If the gate reverses or will not close, leave it open, turn off automatic close if you can, and call. Keep kids from playing in or near the gate path.

Common questions

Why does my gate open but not close?

Most often a photo eye is blocked, dirty or out of alignment, so the opener thinks something is in the way. Clean the lenses and check the indicator lights first.

Why does my gate keep opening by itself?

A failing exit loop, a loop detector that needs adjusting, or a shorted wire can trigger an open command. Each one is tested separately to find the cause.

Can a cracked driveway break a gate loop?

Yes. A crack that crosses the saw cut can stretch or break the loop wire, and water getting into the cut makes it worse over time.

Do I need a safety loop under my gate?

It depends on the gate type, how it closes and whether it closes automatically. We look at how cars and people use the driveway and explain what would add protection.

Can a loop be replaced without tearing out the driveway?

Usually. A new loop goes into a narrow saw cut near the old one, and the cut is sealed afterward.

How much does gate sensor or loop repair cost?

It depends on the parts, the number of loops and any cutting or trenching. Call (469) 634-3100 for pricing and ask about current discounts.

Related gate services

Need safety sensor & loop repair in McKinney?

Open 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.

Call nowGet a quote