Gate Electrical and Wiring Repair in McKinney
Plenty of dead gates have a perfectly good motor. The fault sits in the wiring between the power source, the control box and the devices around it, and finding it takes patient testing rather than swapping parts until something works.
Open 24 hours, 7 days a week

Signs of an electrical fault
No power at the operator
A dark board with a good breaker points to a broken feed wire, a failed transformer or a tripped GFCI outlet somewhere upstream that nobody has noticed.
Works one day, dead the next
Intermittent faults usually come from a loose terminal, a corroded splice or a wire nicked underground that only opens up when it is wet or hot.
Battery keeps going flat
If the battery is new and still drains, the charger, the transformer feeding it or the wiring between them is likely at fault.
Accessories failing together
When the sensors, loop and receiver all act up at once, a shared power wire or a common ground has probably failed.
Trouble after a lightning storm
A nearby strike can travel in on the power feed or on long control wires, taking out a board, a receiver or a surge protector in one hit.
Burn marks or a melted smell
Scorched terminals, melted insulation or a relay that clicks with no result mean the operator should stay switched off until it is checked.
Low-voltage control wiring and underground wire runs
Most of the wiring at a gate is low voltage: the run from the transformer to the operator, the cables to the photo eyes and loop, and the link between the two operators on a dual swing gate. These cables usually cross the driveway underground in conduit, and in our clay soil that conduit moves. Over time it can crack, fill with water and let the wire inside corrode or rub through.
We trace the run, test each conductor, and either repair at an accessible splice or pull new wire. Where the old wire was buried without conduit, replacement usually means new conduit and a fresh run, which may involve trenching or a driveway saw cut.
Transformers, chargers, relays and junction boxes
Gate operators lean on a handful of electrical parts that fail with age and heat: the transformer that steps power down, the battery charger that keeps the backup alive, relays and contactors on the board, fuses, and the terminal blocks where wires land. Inside a sealed control box on a south-facing post, summer heat speeds that wear along.
Typical electrical repairs include:
- Transformer and battery charger replacement
- Relay, contactor, fuse and terminal block repair
- Junction box and enclosure replacement where water has gotten in
- Wiring harness and connector repair at the control board
- Grounding checks and surge protector installation
Surge, lightning and water damage
Spring storms in north Collin County bring lightning, wind and standing water, and gate electronics take the brunt of all three. Lightning damage often shows up as a dead board plus one or two dead accessories. Water damage shows up as green corrosion on terminals and connections, sometimes weeks after the storm has passed.
We test which parts survived before replacing anything, then look at why water got in. Resealing an enclosure, adding a drip loop or raising a box off the ground is often part of the fix.
Solar-to-AC conversion, and where an electrician comes in
Some solar gates in shaded yards never hold a full charge, and some AC gates at the end of long driveways would be simpler to run on solar. We can convert either way where the site suits it, handling the operator side, the low-voltage wiring and the solar equipment.
We are not electricians. If a new line-voltage circuit, a new outlet at the gate or any change to your home panel is needed, a licensed electrician does that work. We tell you what power the operator needs so the electrician can plan the run, and we connect the gate side once it is in place.
What affects the cost
The price depends on how far the fault is from the gate, whether wire can be repaired or must be pulled new, any trenching or saw cutting, and which parts were damaged. Call for pricing, and ask about current discounts.
Check these before you call
- Check the breaker and press reset on any GFCI outlet that feeds the gate
- Look for a status light on the control board or the charger
- Note whether the problem started after a storm, heavy rain or yard work
- Look for chewed, cut or exposed wire where cables enter the control box
- Leave the control box closed if there is standing water or a burning smell
Safety first
Line voltage at a gate can injure or kill, and wet ground makes it more dangerous. Switch the power off at the breaker before touching anything in the control box, and stay clear of the box if you see scorching, smell burning or find water inside. Leave any work on household circuits to a licensed electrician.
Common questions
My outlet has power but the gate board is dead. What is wrong?
The fault is between the outlet and the board: a failed transformer, a broken low-voltage wire, a blown fuse or a bad connection. Each one is quick to test once the box is open.
Can you fix wiring buried under my driveway?
Often, yes. Sometimes the old wire can be pulled out of its conduit and replaced. If it was buried directly or the conduit has collapsed, a new run may need a trench or a saw cut.
Do you run new electrical service to the gate?
No. A licensed electrician runs any new line-voltage circuit. We handle the gate side and can explain what the operator needs so the electrician quotes the right job.
Is it worth switching my solar gate to AC power?
If the panel is shaded or the gate runs many times a day, AC can be more dependable. If bringing power out is costly on your lot, a larger panel and battery may solve it instead. We look at both.
What does gate wiring repair cost?
It depends on where the fault is, how much wire is involved and whether any digging is needed. Call (469) 634-3100 for pricing and ask about current discounts.
Related gate services
Need gate wiring repair in McKinney?
Open 24 hours, 7 days a week. Call for pricing on your gate. Ask about current discounts when you call.